Lucas distributor, ignition coil and amplifier - Series II from May 1975, Series III to September 1981
for Lucas 36DE12 distributor - includes magnet at rear of arm
XJ12 Series II from engine no. 7P25001, Series III to engine no. 7P42299 (1975-79)
Requires: 1
for Lucas 36DE12 distributor - includes magnet at rear of arm
XJ12 Series II from engine no. 7P25001, Series III to engine no. 7P42299 (1975-79)
Requires: 1
for Lucas 36DE12 and 36DM12 distributors
XJ12 Series III from engine no. 7P42300 to 7P45000 (1979--81)
Requires: 1
for Lucas 36DE12 and 36DM12 distributors
XJ12 Series III from engine no. 7P42300 to 7P45000 (1979-81)
Requires: 1
'reed' type - Lucas no.: 54423391
Series II. Trigger board 281073 (ill. 6) can be used alternatively
Requires: 1
'reed' type - Lucas no.: 54419247
Series III. Trigger board 281073 (ill. 6) can be used alternatively
Requires: 1
for 'reed' pick up module inside Lucas 36DE12 distributor
Requires: 1
conversion kit to 'hall' type with 4 connecting wires. Includes rotor arm, board and fitting kit. Replaces 'reed' pick up module
Requires: 1
with vacum code 6-10-8 and push on vacuum pipe. Fits Lucas 36DE12 distributors 41677 and 41742
Series II: all countries less Australia
Requires: 1
retard unit with vacum code code 5-8-7R and push on vacuum pipe. Fits Lucas 36DE12 distributors 41387 and 41591
Series II: Australia exports
Requires: 1
with vacum code 5-8-4R 'retard' and push on vacuum pipe. Fits Lucas 36DE12 distributor 41321
Requires: 1
with vacum code 6-10-8 and push on vacuum pipe. Fits Lucas 36DE12 distributors 41677 and 41742
Series III to VIN...310612 except California exports
Requires: 1
Series II: California exports to VIN 310612
Requires: 1
with vacum code 5-15-12 and push on vacuum pipe. Fits Lucas 36DE12 distributor 41825
Series III from VIN...310612 to engine no. 7P45000 (1979-81)
Requires: 1
distributor
Requires: 1
13 piece - for Lucas 36DE12 and 36DM12 distributor
Requires: 1
13 piece - for Lucas 36DE12 and 36DM12 distributor
Requires: 1
36DE12 type with top entry cap, serial numbers: 41591, 41622, 41677 - reconditioned, in exchange
Series II
Requires: 1
Opus ignition system - please note: this amplifier does no fit to Series I and II models with original ignition amplifier. As an alternative our conversion kit 480002 (complete set incl. pick up module) can be used on these early cars. You only can use the ignition amplifier 209943 when your car was converted original by Jaguar
Requires: 1
made from rubber with 47 mm outer diameter - for 38 mm hole and 10 mm cable, total height: 7.7 mm
Requires: 1
ignition coil, variant for 3+3 connecting wires
Requires: 1
6RA type with 4 Lucar terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
6RA type
Requires: 1
6RA type with 4 Lucar terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
Requires: 1
programmable via USB interface - for Jaguar 12 cylinder engines
Requires: 1
