Tappet adjusting pads

Product number: 490223

124-piece set, supplied in a wooden box with shims from 0.085 to 0.124" (from 2.16 mm to 3.15 mm)

$495.00

excl. Tax

Shipping: Standard

Product Information "Tappet adjusting pads"

Jaguar: All Jaguar fitted with XK and V12 engines (1949-97): XK120, XK140 and XK150 (1949-61) • E-Type Series 1 and 2 (1961-70) • Mark I 3.4 (1957-59) • Mark II 3.4, 340 and 3.8 (1959-69) • S-Type 3.4 and 3.8 (1963-68) • 420 and Daimler Sovereign (1966-69) • Mk7, Mk8 and Mk9 (1950-61) • Mk10 (1961-66) • 420G (1966-70) • XJ6 Series I, II and III (1968-87) • Daimler DS420 Limousine and Hearse (1968-92) • E-Type 5.3 V12 Series 3 (1971-74) • XJ12 Series I, II and III (1972-92) • XJS 5.3 V12 to VIN...188104 (1975-93) • XJ40 (XJ) 6.0 V12 from VIN...673299 to engine no. 8C10462 (1992-93)

Maserati: 3500 GT, 3500 GTI and Vignale Spyder (1957-66) • Sebring (1962-69) • Mistral (1963-70) • Quattroporte I (1963-70) • Mexico (1967-73) • Ghibli (1966-73) • Indy (1969-75) • Bora (1972-78) • Khamsin (1973-82)

124-piece set, supplied in a wooden box with shims from 0.085 to 0.124" (from 2.16 mm to 3.15 mm)

All neatly arranged in a compartment box are three each of shim sizes 0.085” to 0.092”; four each of sizes 0.093” to 0.103” and three each of sizes 0.104” to 0.124” - that’s 120 shims at a retail value of more than 300 pounds! All shims made in Europe with either part number (standard A-Z range) or size (0.111” to 0.124”) laser etched on shim.
op-mounted camshafts in combination with cup tappets have a number of design advantages. The direct drive of the valves has a low profile and allows maximum performance with few moving parts. Tappets with a shim for valve lash adjustment provide a firm connection for actuating the valves. The design is very reliable even under thermal load, very speed-resistant, cannot move and the maintenance intervals are long. The alternative to bucket tappets with shims are bucket tappets with hydraulic valve lash adjustment, in short: hydraulic tappets, which, however, can wear out and are far less solid and therefore less reliable in operation.
Adjusting the valve lash using shims therefore has a number of design advantages that are used in many demanding engines. These include: Many high-revving motorcycle engines, some Alfa and Fiat machines or even the current Jaguar AJ8 engine
When it comes to adjusting the valve clearance, you need a micrometer screw, a calculator, a variety of shims in the back, a feeler gauge and a lot of patience. That's why valve clearance adjustments with shims are considered difficult, but this is not true: With a system and the right tools, valve lash adjustment is quite feasible:
If you do not want to leave the engine open, make sure you have a sufficient supply of shims in advance. Used shims without traces of use can be reused, please check the printed dimension with the help of the micrometer screw. Many shims are labeled in inches and metric. Usually it is much easier to calculate with the metric dimensions. Errors in the conversion range occur, please check the plausibility of the selected shims before assembling.
The oversizes from 3.20 mm to 4.50 mm are exclusively available from us. These oversizes are required when standard camshafts have been re-ground. Either as part of an overhaul, or to extend valve opening times. We also carry undersizes from 2.00 mm to 2.15 mm. These undersizes allow the correct adjustment of the valve lash when the valve seat is heavily worn.